186873 DILDC500/22(RDS250)

Delivery program

Product range
Contactors
Application
DC contactor
Subrange
Comfort devices greater than 170 A
Instructions
DILDC contactors feature an electronic arc suppression system. Because of this, it is important not to exceed any technical data limits in general – especially the making and breaking capacity limits. Opening the device will immediately void the warranty.
integrated suppressor circuit in actuating electronics
Connection technique
Screw connection
Rated operational current, open
DC-1Notes
Ie at 60 °C
DC-11000 V [Ie]
500 A
Can be combined with auxiliary contact
DILM820-XHI…
Actuating voltage
RDS 250: 110 - 250 V 40 - 60 Hz/110 - 350 V DC
Voltage AC/DC
AC and DC operation
Contacts
N/O = Normally open
2 N/O
N/C = Normally closed
2 NC
Auxiliary contacts
possible variants at auxiliary contact module fitting options
on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA
Side mounting auxiliary contacts
2100DRW-97

Technical data

General
Standards
EN60947-4-1, EN60947-5-1
Lifespan, mechanicalAC operated [Operations]
1 x 106
Lifespan, mechanicalDC operated [Operations]
1 x 106
Operating frequency, mechanicalAC operated [Operations/h]
1000
Operating frequency, mechanicalDC operated [Operations/h]
1000
Maximum operating frequencyelectrical (Contactors without overload relay) [Operations/h]
100
Climatic proofing
Damp heat, constant, to IEC 60068-2-78
Damp heat, cyclic, to IEC 60068-2-30
Ambient temperatureOpen
-40 - +70 °C
Ambient temperatureEnclosed
- 40 - + 40 °C
Ambient temperatureStorage
- 40 - + 80 °C
Mounting position
210N040210N018
Mechanical shock resistance (IEC/EN 60068-2-27)Half-sinusoidal shock, 10 msMain contactsN/O contact
10 g
Mechanical shock resistance (IEC/EN 60068-2-27)Half-sinusoidal shock, 10 msAuxiliary contactsN/O contact
10 g
Mechanical shock resistance (IEC/EN 60068-2-27)Half-sinusoidal shock, 10 msAuxiliary contactsN/C contact
8 g
Degree of Protection
IP00
Protection against direct contact when actuated from front (EN 50274)
Covers on main terminals safeguarded against accidental contact with fingers or back of hand
Altitude
Max. 2000 m
WeightWeight
7.5 kg
Terminal capacity main cableFlexible with cable lug
50 - 240 mm2
Terminal capacity main cableStranded with cable lug
50 - 240 mm2
Terminal capacity main cableSolid or stranded
1/0 - 500 MCM AWG
Terminal capacity main cableBusbar [Width]
40 mm
Main cable connection screw/bolt
M10
Tightening torque
24 Nm
Terminal capacity control circuit cablesSolid
1 x (0.75 - 2.5)
2 x (0.75 - 2.5) mm2
Terminal capacity control circuit cablesFlexible with ferrule
1 x (0.75 - 2.5)
2 x (0.75 - 2.5) mm2
Terminal capacity control circuit cablesSolid or stranded
2 x (18 - 12) AWG
Control circuit cable connection screw/bolt
M3.5
Tightening torque
1.2 Nm
ToolMain cableWidth across flats
16 mm
ToolControl circuit cablesPozidriv screwdriver
2 Size
ToolControl circuit cablesStandard screwdriver
0.8 x 5.5
1 x 6 mm
Main conducting paths
Rated impulse withstand voltage [Uimp]
8000 V
Overvoltage category/pollution degree
III/3
Rated insulation voltage [Ui]
1000 V DC
Rated operational voltage [Ue]
1000 V DC
Safe isolation to EN 61140Between control inputs and main contacts
1000 V
Safe isolation to EN 61140Between auxiliary contacts and main contacts
1000 V
Safe isolation to EN 61140between the contacts
1000 V
Making capacity
750 A
Breaking capacity 220 V 230 V
750 A
Breaking capacity 380 V 400 V
750 A
Breaking capacity 500 V
750 A
Breaking capacity 1000 V
750 A
Short-circuit ratingShort-circuit protection maximum fuseType “2” coordination 400 V DC [gR 1000 VDC]
700 (max. short-circuit current 6 kA) A
Short-circuit ratingShort-circuit protection maximum fuseType “2” coordination 690 V DC [gR 1000 VDC]
700 (max. short-circuit current 6 kA) A
Short-circuit ratingShort-circuit protection maximum fuseType “2” coordination 1000 V DC [gR 1000 VDC]
700 (max. short-circuit current 6 kA) A
Short-circuit ratingShort-circuit protection maximum fuseType “1” coordination 400 V DC [gR 1000 VDC]
700(max. short-circuit current 30 kA) A
Short-circuit ratingShort-circuit protection maximum fuseType “1” coordination 690 V DC [gR 1000 VDC]
700 (max. short-circuit current 30 kA) A
Short-circuit ratingShort-circuit protection maximum fuseType “1” coordination 1000 V DC [gR 1000 VDC]
700 (max. short-circuit current 30 kA) A
DC
Rated operational current, openDC-1Notes
Ie at 60 °C
Rated operational current, openDC-11000 V [Ie]
500 A
Current heat loss
1 pole, at Ith
50 W
Magnet systems
Voltage toleranceUS
110 - 250 V 40-60 Hz
110 - 350 V DC
Voltage toleranceAC operated [Pick-up]
0.7 x US min - 1.15 x US max
Voltage toleranceDC operated [Pick-up]
0.7 x US min - 1.15 x US max
Voltage toleranceAC operated [Drop-out]
0.2 x US max - 0.6 x US min
Voltage toleranceDC operated [Drop-out]
0.2 x US max - 0.6 x US min
Voltage toleranceActuation directly from PLCUC
24 V DC
Voltage toleranceActuation directly from PLCUC min - max
15 - 31,2 V DC
Power consumption of the coil in a cold state and 1.0 x USNote on power consumption
Control transformer with uk ≦ 6%
Power consumption of the coil in a cold state and 1.0 x USPull-in power [Pick-up]
600 VA
Power consumption of the coil in a cold state and 1.0 x USPull-in power [Pick-up]
550 W
Power consumption of the coil in a cold state and 1.0 x USSealing power [Sealing]
18 VA
Power consumption of the coil in a cold state and 1.0 x USSealing power [Sealing]
9.5 W
Duty factor
100 % DF
Changeover time at 100 % US (recommended value)Main contactsClosing delay
80 ms
Changeover time at 100 % US (recommended value)Main contactsOpening delay
40 ms
PLC signal level (A3 - A4) to IEC/EN 61131-2 (type 2)High
15 V
PLC signal level (A3 - A4) to IEC/EN 61131-2 (type 2)Low
5 V
Electromagnetic compatibility (EMC)
Electromagnetic compatibility
This product is designed for operation in industrial environments (environment A). Its use in residential environments (environment B) may cause radio-frequency interference, requiring additional noise suppression measures.
Rating data for approved types
Switching capacityMaximum motor ratingSingle-phaseGeneral use
500 A
Auxiliary contactsPilot DutyAC operated
A600
Auxiliary contactsPilot DutyDC operated
P300
Auxiliary contactsGeneral UseAC
600 V
Auxiliary contactsGeneral UseAC
15 A
Auxiliary contactsGeneral UseDC
250 V
Auxiliary contactsGeneral UseDC
1 A

Design verification as per IEC/EN 61439

Technical data for design verification
Rated operational current for specified heat dissipation [In]
500 A
Heat dissipation per pole, current-dependent [Pvid]
50 W
Equipment heat dissipation, current-dependent [Pvid]
0 W
Static heat dissipation, non-current-dependent [Pvs]
9 W
Heat dissipation capacity [Pdiss]
0 W
Operating ambient temperature min.
-40 °C
Operating ambient temperature max.
+70 °C
IEC/EN 61439 design verification
10.2 Strength of materials and parts10.2.2 Corrosion resistance
Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.3.1 Verification of thermal stability of enclosures
Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.3.2 Verification of resistance of insulating materials to normal heat
Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.3.3 Verification of resistance of insulating materials to abnormal heat and fire due to internal electric effects
Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.4 Resistance to ultra-violet (UV) radiation
Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.5 Lifting
Does not apply, since the entire switchgear needs to be evaluated.
10.2 Strength of materials and parts10.2.6 Mechanical impact
Does not apply, since the entire switchgear needs to be evaluated.
10.2 Strength of materials and parts10.2.7 Inscriptions
Meets the product standard's requirements.
10.3 Degree of protection of ASSEMBLIES
Does not apply, since the entire switchgear needs to be evaluated.
10.4 Clearances and creepage distances
Meets the product standard's requirements.
10.5 Protection against electric shock
Does not apply, since the entire switchgear needs to be evaluated.
10.6 Incorporation of switching devices and components
Does not apply, since the entire switchgear needs to be evaluated.
10.7 Internal electrical circuits and connections
Is the panel builder's responsibility.
10.8 Connections for external conductors
Is the panel builder's responsibility.
10.9 Insulation properties10.9.2 Power-frequency electric strength
Is the panel builder's responsibility.
10.9 Insulation properties10.9.3 Impulse withstand voltage
Is the panel builder's responsibility.
10.9 Insulation properties10.9.4 Testing of enclosures made of insulating material
Is the panel builder's responsibility.
10.10 Temperature rise
The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
10.11 Short-circuit rating
Is the panel builder's responsibility. The specifications for the switchgear must be observed.
10.12 Electromagnetic compatibility
Is the panel builder's responsibility. The specifications for the switchgear must be observed.
10.13 Mechanical function
The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.

Technical data ETIM 7.0

Low-voltage industrial components (EG000017) / Power contactor, DC switching (EC002552)
Electric engineering, automation, process control engineering / Low-voltage switch technology / Contactor (LV) / Power contactor, d.c. switching (ecl@ss10.0.1-27-37-10-18 [ACN974011])
Rated control supply voltage Us at AC 50HZ
110 - 250 V
Rated control supply voltage Us at AC 60HZ
110 - 250 V
Rated control supply voltage Us at DC
110 - 350 V
Voltage type for actuating
AC/DC
Rated operation power at DC-3 / DC-5 at 440 V
0 kW
Rated operation current Ie at DC-3 / DC-5 at 440 V
0 A
Modular version
No
Number of auxiliary contacts as normally open contact
2
Number of auxiliary contacts as normally closed contact
2
Type of electrical connection of main circuit
Connection rail
Number of normally closed contacts as main contact
0
Number of main contacts as normally open contact
2

Approvals

Product Standards
IEC/EN 60947-4-1; UL508; CSA-C22.2 No. 14-05; CE marking
UL File No.
E338590
UL Category Control No.
NRNT
CSA File No.
012528
CSA Class No.
C321124
North America Certification
UL listed, CSA certified
Specially designed for North America
No

Characteristics

Side mounting auxiliary contacts
2100DRW-97
possible variants at auxiliary contact module fitting options
on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA

Dimensions

2100DIM-49